Phone: +1 (307) 441-5529
Mail:info@vovlift.com
Mon to Fri (10 AM to 6 PM) ET
Phone: +1 (307) 441-5529
Mail:info@vovlift.com
Mon to Fri (10 AM to 6 PM) ET






Storage and organization is not one purchase decision, it is a set of them, driven by what you are storing, how often you touch it, and how much floor you can afford to give up. Start with the load: palletized goods, long stock such as bar and pipe, flat goods such as sheet and slab, drums and cylinders, cable reels, small parts, or hand tools. Each has a structure built for it, and forcing the wrong one into service is the most common and most expensive mistake buyers make. Then look at throughput — fast-moving parts belong at waist height in a flow lane or a carousel, while slow movers can go high, deep, or outside. Finally check the site: slab condition, clear height under sprinklers and lighting, aisle width for whatever truck serves the area, and whether the material you are storing is regulated.
Long and flat material is where general-purpose shelving fails. Cantilever racks, offered here as standard and galvanized kits, carry bar, pipe, lumber and extrusion on open arms with no front column in the way, so material loads from the side in full lengths. ANSI MH16.3 is the standard covering the design, testing and utilization of industrial steel cantilevered storage racks, and it is the document your engineer or insurer will reference. Sheet and slab want a different geometry: the Standard Sheet Rack (VSSR) and Horizontal Sheet Rack (SHEET) hold panel goods without bowing, while the Slab Transport Rack (STR) is built to move slab material rather than just park it. Bar stock sorted by size or alloy is better served by a Long Bar Pigeon Hole Rack (LBPH) or a Double Sided Horizontal Bar Rack (DSHZ), where every cell is its own location. Reel Racks (RERC) support spools on axles so cable pays out instead of being unstacked, and Gantry Sling Racks (SLR) get slings off the floor — worth pairing with the inspection routine ASME B30.9 sets out for slings.
Several items here upgrade racking you already own. Pallet Rack Gravity Flow Shelves (GFL) and Carton Flow Racks (FLOW) convert static beam levels into first-in, first-out lanes, which matters for dated stock and cuts walking in a pick module. Lane width follows your carton or pallet footprint; the GMA standard grocery pallet is 48 by 40 inches, and if you run mixed footprints, size lanes to the largest. Pallet Rack Security Gates (RDHG) close off open bays where product is exposed to traffic or theft, and the Pallet Rack Sump (PRS) contains leaks from drums or totes stored on beam. ANSI MH16.1 covers the design, testing and utilization of industrial steel storage racks, and OSHA 1910.176 requires storage areas be kept free of hazards with aisles and passageways clear. Most rack failures begin as an unreported forklift strike on an upright.
For small parts and consumables the choice is between static shelving, roll-out shelving and powered carousels. Heavy Duty Roll-Out Shelving (VRSOR) pulls the whole shelf into the aisle so operators reach deep stock without climbing. Stainless options — Stainless Steel Solid Rivet Shelving (LWSS), Stainless Steel Shelving (SSS) and Stainless Steel Lockers (LOCK) — suit food, pharmaceutical and washdown areas where painted steel corrodes. Powered carousels bring parts to the operator instead: the Stand Alone Powered Carousels (STPC) line lists three models rated at 4,000 lb, including a chain-driven AC unit on a 48 in. diameter. Low-Profile Powered Carousels and Pail Carousel Racks serve the same idea in shorter and container-specific formats. At the bench, Manual Adjustable Ergonomic Work Benches (EWB) come in 60 x 30 in. and 72 x 36 in. sizes, while the Linear Actuated Adjustable-Height Work Bench (LAW-3636) changes height under power for shared or sit-stand stations.
Two families here are regulated, and buying on price alone is a mistake. Flammable Safety Cabinets (FLSC) exist to satisfy OSHA 1910.106, which limits a storage cabinet to no more than 60 gallons of Category 1, 2 or 3 flammable liquids and no more than 120 gallons of Category 4 liquids, and requires the cabinet be conspicuously labeled FLAMMABLE — KEEP FIRE AWAY. NFPA 30 is the companion code most fire marshals enforce. For gas, Cylinder Storage Cabinets are listed alongside galvanized and propane-exchange versions. OSHA 1910.253 requires oxygen cylinders in storage be separated from fuel-gas cylinders by at least 20 feet, or by a noncombustible barrier at least 5 feet high with a fire-resistance rating of at least one-half hour, and that cylinders be secured upright with valve protection caps in place.
Storage Buildings (STOR) and Multi-Duty Storage Buildings (MDS) push overflow, grounds equipment and shelter functions outside the four walls. The STOR line lists five models, from a 4 ft. by 4 ft. locker up to a 6 ft. by 6 ft. wide-door building. The MDS line lists six models at 120 in., including a bicycle shelter, a smokers shelter and a shed with front doors. All are made in the USA by Vestil with Vestil's limited warranty, whose period depends on the model (most Vestil products here: 90 days on original components) — see the Warranty tab on each product page. Before ordering, confirm you have a level, load-bearing pad with anchorage, and check whether your jurisdiction permits an accessory structure. On the housekeeping side, Vestil Electric Hydraulic Trash Can Dumpers are offered in AC and DC models rated at 400 lb with a 74 in. dump height. OSHA 1910.22 requires walking-working surfaces be kept clean and orderly, and a defined place for scrap is the cheapest way to hold that standard.
The collection covers Vestil storage and organization equipment: cantilever, sheet, bar, slab and reel racks; gravity flow and carton flow shelving; stainless and roll-out shelving; powered carousels; work benches; tool boxes and lockers; flammable and cylinder cabinets; and outdoor storage buildings and shelters.
Use cantilever rack for long stock. Its arms have no front column, so bar, pipe, lumber and extrusion load from the side in continuous lengths instead of being cut to fit between uprights. Pallet rack suits unitized loads on pallets. ANSI MH16.3 covers design, testing and utilization of industrial steel cantilevered storage racks; ANSI MH16.1 covers standard industrial steel storage racks.
OSHA 1910.106 limits a flammable liquid storage cabinet to no more than 60 gallons of Category 1, 2 or 3 flammable liquids, or no more than 120 gallons of Category 4 liquids, and requires it be conspicuously labeled FLAMMABLE — KEEP FIRE AWAY. NFPA 30 is the companion code most fire marshals enforce. Confirm cabinet counts per control area locally.
Yes. OSHA 1910.253 requires oxygen cylinders in storage be separated from fuel-gas cylinders and combustibles by at least 20 feet, or by a noncombustible barrier at least 5 feet high with a fire-resistance rating of at least one-half hour. Cylinders must be secured upright with valve protection caps in place.
The Stand Alone Powered Carousel (STPC) line lists three models, all rated at 4,000 lb, including the STPC-WH and a chain-driven AC carousel on a 48 in. diameter. Low-Profile Powered Carousels and Pail Carousel Racks are listed separately, so check each product page for its own rating.
Choose the stainless lines: Stainless Steel Solid Rivet Shelving (LWSS), Stainless Steel Shelving (SSS) and Stainless Steel Lockers (LOCK). Painted or plated steel corrodes under repeated washdown and sanitizing chemicals, and flaking coating becomes a contamination risk. For damp or outdoor storage that does not require stainless, the galvanized cantilever rack kits and galvanized cylinder cabinets are the more economical route.
Manual adjustment fits benches set once for a task or an operator; the Manual Adjustable Ergonomic Work Benches (EWB) come in 60 x 30 in. and 72 x 36 in. sizes. Choose the Linear Actuated Adjustable-Height Work Bench (LAW-3636) when height changes between shifts or between seated and standing work, because powered adjustment actually gets used.
Usually, but verify first. Gravity flow shelves, security gates and sumps mount to rack you already own, so confirm beam and upright capacity with your rack manufacturer before adding load. ANSI MH16.1 covers the design, testing and utilization of industrial steel storage racks, and OSHA 1910.176 requires storage areas be kept free of hazards with aisles and passageways clear.