Do all mini skid steers use the same attachments?

No. Mini skid steer mount plates vary by brand and model, so an attachment has to list your machine. The Loflin Fabrication Mini Auger is offered for Toro Dingo and Bobcat MT50, 52, 55, S70 and RC30 mounts. Hydraulic flow matters as much as the plate: this auger is rated for 6 to 40 GPM, so confirm your loader's auxiliary output falls inside that band.

Do mini skid steer attachments work on a full-size skid steer?

Not without an adapter. Full-size skid steers use the larger universal quick-attach plate, while this auger is built for the mini mounts listed above. Adapter plates exist, but a full-size machine's higher flow and weight can overload a mini-rated attachment. Check flow first — this drive is rated 6 to 40 GPM — and confirm the loader can be run within that range.

What are the different types of auger bits?

Most bits fall into three groups: standard earth or dirt augers for soil and loam, wider-flight tree or nursery bits for planting, and rock augers with carbide teeth for shale, caliche and frozen ground. All index onto the drive's output shaft, which is 2" hex on this unit, and the Loflin Fabrication Mini Auger accepts bits from 4" to 48" in diameter.

How much hydraulic flow does this auger need?

The Loflin Fabrication Mini Auger is rated for 6 to 40 GPM, which covers most mini skid steer auxiliary circuits. Below the low end the bit turns too slowly to cut efficiently; above the top end you risk heat and seal damage. Check your loader's auxiliary flow and relief pressure in its operator manual, and match couplers — this unit uses Parker hoses, fittings and couplers.

Can you put this auger on a mini excavator?

Not as sold. This drive is built for mini skid steer loader mounts: Toro Dingo and Bobcat MT50, 52, 55, S70 and RC30. Excavator augers hang from the boom on a hanger bracket and pin set sized to that machine, and many excavator auxiliary circuits also need a case drain return. For auger work off an excavator, buy an excavator-specific drive and bracket.

Mini Skid Steer Auger Attachments

This collection covers mini skid steer auger attachments for post holes, footings, fence lines and tree planting. It carries one unit: the Loflin Fabrication Mini Auger at $3,638, built from 3/8" steel with an Auburn planetary drive, a 2" hex output shaft and Parker hoses, fittings and couplers. It runs on 6–40 GPM and mounts to Toro Dingo, Bobcat MT50, 52, 55, S70 and RC30 machines.

Sort by

View as

Loflin Fabrication Mini Auger

$3,638.00 - $3,638.00

$3,638.00

$3,638.00 - $3,638.00

$3,638.00

Available to order

Buy Now, Pay Later

Loflin Fabrication Mini Auger Effortlessly complete drilling tasks with the Loflin Fabrication Mini Skid Steer Auger, built for power and precision...

View full details

$3,638.00 - $3,638.00

$3,638.00

$3,638.00 - $3,638.00

$3,638.00

Top Picks

Loflin Fabrication Mini Auger

Compact-loader auger for clean post holes in tight-access jobs.

$3,638.00

Mini Skid Steer Auger Attachments: What Fits What

A mini skid steer auger attachment is a hydraulic motor and planetary gearbox that hangs on the loader's attachment plate and drives a bit through an output shaft. Two things decide whether one will work on your machine: the mount pattern and the auxiliary hydraulic flow your loader puts out. Get either wrong and the attachment either will not hang or will not turn under load.

This collection carries a single unit, the Loflin Fabrication Mini Auger at $3,638. Its published specifications:

Output shaft	2" hex, industry-standard
Bit size range	4" to 48" diameter
Drive system	Auburn planetary drive
Flow requirement	6–40 GPM
Steel thickness	3/8" thick steel construction
Hydraulic components	Parker hoses, fittings and couplers
Mount compatibility	Toro Dingo, Bobcat MT50, 52, 55, S70, RC30
Finish	Powder-coated

Picking a Bit Diameter

Diameter drives torque demand more than depth does. A 4" bit for sign posts and fence line will spin in almost anything the loader can feed it; a 48" bit for deck footings or tree planting asks for everything the drive and the machine's flow can give, and it will try to turn the loader instead of the bit if the ground grabs. Two common mistakes: sizing the hole to the finished post rather than to the concrete collar around it, and buying one general-purpose earth bit for ground that really needs carbide teeth. Rocky, frozen or caliche soil chews up standard dirt bits and stalls the drive — a rock bit costs more and cuts slower, but it survives.

Digging Safely and Keeping the Drive Alive

Before any hole goes in, contact 811, the national call-before-you-dig number, so utility owners can locate and mark buried lines; notification is required by state one-call law. On construction sites, OSHA's excavation standard at 29 CFR 1926 Subpart P governs excavation work, and OSHA 29 CFR 1926.21 requires employers to train workers on the hazards of the equipment they operate. Auger work adds its own: never clear a wrapped root or loose spoil off a turning bit, and keep bystanders clear of the flight.

Maintenance is short. Wipe and cap the Parker couplers before connecting, check gearbox oil and hardware torque at the interval in the manufacturer's manual, and watch the pilot bit and teeth — a dull pilot makes the auger walk instead of pulling itself into the ground. Powder-coated steel holds up outdoors, but touch up gouges before they rust.