Skip to content
Flag FREE SHIPPING ON SELECTED BRANDS & NO SALES TAX FREE SHIPPING ON SELECTED BRANDS & NO SALES TAX
Tag Take $100 Off Orders Over $2000! | CODE $100 OFF CODE WELCOME

Guns & Wands

Pressure washer guns and wands are the parts an operator holds every shift, and they are usually the first components to fail on a working machine. This category collects replacement and upgrade options from BE Power Equipment: straight gun and wand assemblies in 36-, 47-, 59- and 79-inch lengths, insulated and stainless steel wands for hot water work, telescoping wands that extend to 12, 18 and 24 feet, gutter cleaner attachments, and specialty spray guns including low-pressure, weeping and high-temperature shut-off models.

Filters

There are no products matching your search

View all products

Pressure Washer Guns and Wands: What This Category Covers

A pressure washer gun and wand is the operator end of the system: the trigger gun controls flow, and the wand (or lance) carries that flow out to a nozzle at a working distance. Everything in this collection comes from BE Power Equipment, and most of it sits in replacement-part territory rather than capital spending. The range covers four broad jobs. Straight gun and wand assemblies handle general washing. Insulated and stainless steel wands are built for heated water. Telescoping wands and gutter cleaner attachments move the spray up and away from the operator. Specialty guns — low pressure, weeping, horizontal, and surface-cleaner guns — solve narrower problems that a standard trigger gun handles poorly.

How to Choose a Pressure Washer Gun and Wand

Start with the machine, not the wand. The gun and wand you buy must be rated at or above the pressure and temperature your pressure washer produces, and it has to thread or couple to what is already on the hose. Underrating the gun is the most common purchasing mistake in this category: a gun rated for a cold-water consumer unit will not survive on a hot-water commercial machine, and the failure usually happens at the trigger under load.

Length is the second decision, and it is mostly about reach and control. Longer wands cover more area per pass and keep the operator further from splashback, but they load the wrists more over a full shift because of the leverage. Shorter wands give better control in tight work and around detail.

Wand length in this collectionTypical use
18-inch flex wandDetail and awkward-angle work where a rigid wand cannot be aimed
29-inch gutter cleaner kitCurved gutter work from a ladder or as part of an extension setup
36-inchVehicle and equipment washing, close-quarters cleaning, high control
47-inch and 59-inchGeneral-purpose siding, concrete, fleet and shop work
79-inchMaximum standing reach on a fixed wand; walls, trailers, tall equipment
12-, 18- and 24-foot telescopingSecond-story siding, gutters, soffits and overhead work from the ground

Telescoping Wands and Gutter Cleaners for Overhead Work

The 12-, 18- and 24-foot telescoping wands exist for one reason: they let an operator clean high surfaces while standing on the ground. That matters commercially because ladder work is where washing crews get hurt, and OSHA's general industry ladder rules (29 CFR 1910.23) impose requirements on ladder condition and use that a ground-based tool sidesteps entirely.

Telescoping wands are heavier and more awkward than fixed wands, and the load grows as the wand extends. Buyers routinely underestimate this. Plan on a belt or harness for full extension work, keep the extension no longer than the job needs, and check the locking collars before every use. The collection also carries a replacement gun assembly for telescoping wands, which is worth knowing about because the gun end typically wears out long before the pole does.

For gutters specifically, the collection includes curved gutter cleaner attachments in M22 and 1/4-inch quick connect versions plus the 29-inch gutter cleaner wand kit. These clip onto an existing wand and turn the spray back into the trough, so debris is pushed out rather than packed down.

Hot Water, Insulated Wands and High-Pressure Duty

Hot water changes what the operator can hold. Insulated wands — offered here in 36-, 47-, 59- and 79-inch lengths, in both standard and stainless steel versions — carry a covering that keeps the tube surface from becoming a burn hazard. If your machine is a hot-water unit, an insulated wand is not an upgrade, it is the correct part. Stainless steel versions add corrosion resistance, which matters where detergents, salt, food processing residue or wash-bay chemistry are involved.

At the top of the pressure range, this collection carries a 5,000 PSI commercial high temperature shut-off gun and a 5,000 PSI spray gun. A shut-off gun stops flow at the gun when the trigger is released, which is standard practice on commercial machines. There is also a 47-inch dual lance with hot water gun for operators who need to switch between spray patterns without changing tools.

Connections, Fitment and Replacement Parts

Fitment is where orders go wrong. M22 is the common threaded connection on residential and light commercial machines, and several items here are specified as M22, including the gutter cleaner attachment and the 3000 PSI electric pressure washer accessory kit. Quick connect couplers are the other pattern; the collection includes a 1/4-inch quick connect gutter cleaner. Before ordering, check the fitting on your hose and on your existing gun, note the thread or coupler size, and confirm your machine's pressure and maximum inlet temperature.

Some items here are component-level rather than complete assemblies — front lance assemblies, gun assemblies for specific wand families, and guns designed for particular BE wand models. These are the right choice when one part has failed and the rest of the assembly is sound. If both ends are worn, a complete gun and wand assembly usually costs less than replacing the pieces separately.

Safety, Maintenance and Operator Practice

High-pressure water injection injuries are a genuine medical emergency, not a bad scrape, and they are caused by the same stream that cleans concrete. OSHA's general PPE standard (29 CFR 1910.132) requires employers to assess workplace hazards and provide appropriate protective equipment, which for pressure washing normally means eye protection, gloves and non-slip footwear at minimum.

On maintenance, most gun and wand failures announce themselves. Watch for a trigger that leaks when released, a gun that will not fully shut off, stiff or gritty trigger action, and weeping at the wand-to-gun joint. Replace O-rings before they blow rather than after. Relieve pressure and disconnect the machine before changing any component, and never bypass or tape down a trigger safety latch. Store wands straight and dry; a bent wand fatigues at the bend and fails there.

Guns & Wands: Frequently Asked Questions

What pressure washer gun and wand length should I buy?

Pick by the work, not the highest number. This collection offers 36-, 47-, 59- and 79-inch assemblies. Shorter wands give better control for vehicles, equipment and detail work. The 47- and 59-inch sizes cover most general siding, concrete and fleet washing. The 79-inch gives the longest fixed reach for walls, trailers and tall equipment, at the cost of more wrist load over a full shift.

Will these guns and wands fit my pressure washer?

Check two things before ordering: the connection type and your machine's pressure and temperature rating. Several items here are specified as M22, including the gutter cleaner attachment and the 3000 PSI accessory kit, and there is a 1/4-inch quick connect gutter cleaner. The gun must be rated at or above what your machine produces. Some assemblies are designed for specific BE wand models, so confirm fitment against your existing setup.

What is the difference between insulated and stainless steel insulated wands?

Both carry insulation that keeps the tube surface from becoming a burn hazard on hot-water machines, and both are offered here in 36-, 47-, 59- and 79-inch lengths. The stainless steel versions add corrosion resistance to the wand tube itself, which matters in wash bays, food processing, coastal or salt environments, and anywhere aggressive detergents are used regularly.

Do I need a telescoping pressure washer wand or a gutter cleaner attachment?

They solve different problems. Telescoping wands — 12, 18 and 24 feet here — extend your reach for second-story siding, soffits and overhead surfaces from the ground. Gutter cleaner attachments are curved fittings that direct spray back into the gutter trough to push debris out. Many crews use both: the telescoping wand for reach, with a gutter attachment or the 29-inch gutter cleaner kit fitted at the end.

What is a weeping spray gun used for?

A weeping gun allows a small continuous bleed of water rather than shutting off completely at the trigger. It is used in freezing conditions to keep water moving through the gun and hose so the line does not freeze during pauses in work. This collection includes a standalone weeping pressure washer spray gun and an 18-inch flex wand assembly paired with a weeping gun.

How do I know when to replace my pressure washer gun?

Replace when the trigger leaks after release, when the gun will not fully shut off, when trigger action turns stiff or gritty, or when water weeps at the wand-to-gun joint. These signs precede a failure under pressure. If only one end is worn, component-level replacements such as gun assemblies and front lance assemblies are available here; if both ends are tired, a complete gun and wand assembly is usually the better buy.

What safety equipment should operators use with pressure washer guns and wands?

High-pressure water can cause injection injuries that require emergency medical treatment, so treat the gun as a tool, not a hose. OSHA's general PPE standard (29 CFR 1910.132) requires employers to assess hazards and provide appropriate protective equipment; for pressure washing this normally means eye protection, gloves and non-slip footwear. Never disable a trigger safety latch, and relieve system pressure before changing any wand or gun.

What brands and price range does this collection cover?

All items in this collection are BE Power Equipment products. The range covers small component parts such as front lance assemblies and replacement gun assemblies at the low end, through complete gun and wand assemblies, insulated and stainless wands, and telescoping wands and gutter cleaning kits at the upper end of the range. Current prices are listed on each product page.

Have a question? Talk to an expert today!

We can help you find your perfect attachment
Free Shipping
Free Shipping

Enjoy free shipping on selected brands & no sales tax!

Freight Damage Support
Freight Damage Support

Inspect your delivery and note any damage on the delivery receipt. Damage claims follow our Return & Refund Policy.

USA Customer Support
USA Customer Support

Speak to a sales rep or forklift expert.

Payment & Security
Payment & Security

We use encrypted SSL security to ensure that your credit card information is protected.

Request a CallbackMon–Fri 10–6 ET